JSR GT12 Toe-In Gauge

JetsetRobot are pleased to announce the re-release of our GT12 Toe-In Gauges. CNC machined from acrylic and delrin, these GT12 toe-in gauges allow you to set up the front end of your GT12 car precisely each time.
The gauges can be purchased here, while the board is simply downloaded and printed on a piece of A4 paper. When printing the board, be careful to print at 100%.

The Board can be downloaded here

JSR Stainless Steel RC Screw Set.

We are pleased to announce the release of our new JSR stainless Steel Screw Kit for RC vehicles.

A2 Stainlness Steel M3 socket screws in a range of popuar sizes. Our screw sets contain countersunk, dome & socket head screws in various lengths from 5mm to 40mm. The contents of our screw sets have been chosen to provide most, if not all of the required M3 screws for many of the popular 1:10 scale RC racing cars on the market today. The picture shows the actual amount of screws included.

The JSR Racer’s Assortment contains:

  • Countersunk Screws
  • M3 x 6mm. Quantity 15
  • M3 x 8mm. Quantity 25
  • M3 x 10mm. Quantity 15
  • M3 x 12mm. Quantity 15
  • M3 x 20mm. Quantity 5
  • M3 x 25mm. Quantity 5
  • M3 x 30mm. Quantity 2
  • Dome Head Screws
  • M3 x 6mm. Quantity 15
  • M3 x 8mm. Quantity 25
  • M3 x 10mm. Quantity 15
  • M3 x 12mm. Quantity 15
  • M3 x 20mm. Quantity 15
  • M3 x 25mm. Quantity 5
  • M3 x 30mm. Quantity 2
  • Socket Head Screws
  • M3 x 5mm. Quantity 5
  • M3 x 6mm. Quantity 5
  • M3 x 8mm. Quantity 10
  • M3 x 10mm. Quantity 5
  • M3 x 12mm. Quantity 5
  • M3 x 14mm. Quantity 5
  • M3 x 16mm. Quantity 5
  • M3 x 20mm. Quantity 5
  • M3 x 25mm. Quantity 5
  • M3 x 30mm. Quantity 2
  • M3 x 35mm. Quantity 2
  • M3 x 40mm. Quantity 2

Total 220 Screws

Our screw sets are available to purchase from ebay

http://www.ebay.co.uk/sch/jetsetrobot/m.html?_nkw=&_armrs=1&_ipg=&_from=

JSR 1:10 Off Road Shock Protectors

JSR 3D printed shock protectors

We are pleased to announce the release of our new JSR 1:10 Off Road Shock Protectors. These are 3D Printed in Semiflex from Fenner Drives, the makers of Ninjaflex, on a P3 Steel at 0.2mm layer height with a speed of 15mm/s. Initial versions of the covers were printed in PLA first, then PLA/PHA mix for added strength but they required more flexibility during an impact which is why we chose Semiflex.

This specialized filament required alot of dialing in to achieve good results but once we had reduced the print speed and played around with the temperature, the finish was great. I am using an E3D V6 lite, which allows me to extend the PTFE sleeve to just below the hobbed direct drive. This is needed for printing such a flexible filament.

We have carried out extensive testing with the shock protectors and are now happy to offer them for sale. They are just £9.95 per pair plus postage and are available to purchase from ebay.

http://www.ebay.co.uk/sch/jetsetrobot/m.html?_nkw=&_armrs=1&_ipg=&_from=